Tech Center Services & Pricing
Effective: January 1st. 2012
Labor / Grip Installation (per grip) All Grips are Laser Aligned when Installed: ♣ $4.50 ♣
Per Grip With Customer Supplied Grips: ♣ $5.50 ♣
♣ There are sometimes extenuating circumstances which may increase the cost
of old grip removal and the subsequent tape. Carpet Tape, Rubber Glue,
excessive build up tape, Leather Grips, etc. If we find one of these situations
while in the regripping process, we'll call to inform you of the adjusted labor rate. ♣
**Shaft Cut Down: $3.50
**Labor / Shaft Extension: $6.00
.560, .580, .600, 620 Diameter Steel Shaft Extensions: $5.50
Oversize Butt Extension: $6.00
Graphite Shaft Extension (Superlite or Standard): $6.00
We now Do Custom Metal Wood Bending. Loft & Lies. Opening and Closing Faces. Hybrids, Fairway Woods & Drivers. Most shafts will have to be removed from head. Pricing based on degree of difficulty
Adjust Lie &/or Loft on Irons & Some Putters: $8.00 Per Club
Re-Epoxy Iron Club Head: $20.00
Re-Epoxy Wood/Hybrid Head: $30.00
Drill Out/Remove Broken Shaft: *TBD*
Frequency / Spine Align / FLO of Shaft: $20.00
Labor / Steel Shaft Installation / *New: $25.00
Labor / Graphite Shaft Installation / *New: $35.00
*The above pricing is for a new shaft installation only. All Customer
supplied pull out installs will be quoted on an individual basis. On a pull out,
if there is epoxy in the tip, it must be drilled out in order for the air to
escape when installing the subsequent shaft. When drilling out this epoxy it is conceivable
that a small piece may get pushed into the shaft, creating a rattle. At this point the grip
must be removed in order to get the remnant piece of epoxy out. It is the customer's decision whether or not
to buy the grip here & have us install it, to simply supply one to us on his own or to take the club un-gripped,
and do the work himself. In any event, we will not let the club out until the rattle has been removed. While
the customer may say the rattle won't bother him, it is a direct reflection on us and compromises our never
ending quest to craft with the utmost quality, unmatched by anyone.
Thanks for your understanding.*
Labor / Bore Through Installation Callaway®, Titleist, Ping® Steel or Graphite: $50.00
Labor / Titleist 900 Series Shaft Replacement. Includes mandatory replacement of OEM Aluminum Hosel/Sleeve, if applicable. Add $20.00 for Frequency, FLO, Spine Align of Customer Supplied Shaft: $65.00
Shaft Torque Analysis: $10.00
Internal Club Head Weighting (Hot Melt): *$35.00*
*The price above is for the Hot Melting service only* If a shaft has to be removed,
a hole has to be drilled, or anything to be done to access the cavity, an additional
charge will be required.
Counterbalancing of Shaft: $10.00
Shaft Swapping / May require the installation of a new grip. All Titleist and Callaway Bore-Thru Heads will be Quoted on an individual basis. Graphite or Steel: $60.00
Iron Hosel Porting / Removing weight from hosel bore. Essential, but not necessary, for building over length iron sets, wedges, individual irons, etc., to achieve proper swingweight : $25.00 per head
Custom Blue Print Iron Set (8 irons). Labor Only: $480.00
Each Additional Iron for Blueprinting. Labor Only: $60.00
Shaft Profiling with Computer Printout: $19.95
Custom Fitting On FlightScope Launch Monitor (At Ace of Clubs): **$150.00**
**The average club fitting takes 1.25 to 1.5 hours. Additional time, if available on the launch monitor, will be charged out at $25.00 for each additional 15 minutes**Custom Fitting (Site Specific): *TBD*
High Performance, 3 Dimension Putter Fitting using State of the Art technology with the Zenio®, Advanced Putter Fitting System. Video with Motion Analysis. Fitting includes proper length, lie, and loft: $100.00
Callaway or Taylor Made, Tour Clocking Ferrules: $25.00
All Callaway, Ping & Taylor Made Clubs, Requiring a Special OEM Bushing, Sleeve or Ferrule will be Supplied at an Additional Cost: *TBD*
** There’s an Additional Charge for Grip Installation of $4.00 if performed in conjunction with Either of these (2) Services.
*TBD* = To Be DeterminedWe also do Club Head Refinishing on Metal Wood, Persimmon, Iron & Wedge Heads. Wedges can be Refinished with Tour Satin or a Bright Chrome Finish. Also Available are USGA Approved, Tour Box Grooves: Quoted On A Per Piece/Set Basis
We Now Offer Iomic Grips!
![[Matrix Ozik M2 Series Shaft]](M2Series1.jpg)
